當前位置:歐亞貿易網 > 技術中心 > 所有分類

| 編號 | 中文名稱 | 英文名稱 |
|---|---|---|
| EN 125200-1991 | 分規范:線性變壓器用磁性氧化磁芯 | Sectional specification: magnetic oxide cores for linear transformers |
| EN 125400-1991 | 分規范:用于電感器和調諧變壓器中的磁性氧化磁芯的調節器 | Sectional specification: adjusters used with magnetic oxide cores for use in inductors and tuned transformers |
| EN 125401-1991 | 空白詳細規范:用于電感器和調諧變壓器中的磁性氧化(鐵氧體)磁芯的調節器 | Blank detail specification - Adjusters used with magnetic oxide (ferrite) cores for use in inductors and tuned transformers |
| EN 125500-1996 | 分規范:抑制干擾和低電平信號變壓器用環形磁性氧化磁芯 | Sectional specification: Magnetic oxide ring cores for interference suppression and low level signal transformer applications |
| EN 2591-704-2001 | 航空航天系列 光電連接元件 試驗方法 第704部分:電氣元件 耦合器用變壓器匝數比的測量 | Aerospace series - Elements of electrical and optical connection; Test methods - Part 704: Electrical elements; Measurement of turns ratio on a transformer used in a coupler |
| EN 50152-3-3-2001 | 鐵路應用 固定裝置 交流開關的特殊要求 第3-3部分:專門用于交流牽引系統的測量、控制和保護裝置 單相 | Railway applications - Fixed installations- Particular requirements for a.c. switchgear - Part 3-3: Measurement, control and protection devices for specific use in a.c. traction systems- Single-phase inductive voltage transformers |
| EN 50180-1997 | 充液變壓器用1kV至36kV和250A至1.25kA的套管 | Bushings above 1 kV up to 36 kV and from 250 A to 3,15 kA for liquid filled transformers |
| EN 50181-1997 | 不包括充液變壓器在內的設備用1kV至36kV和250A至1. 25kA的插入套管 | Plug-in type bushings above 1 kV up to 36 kV and from 250 A to 1,25 kA for equipment other than liquid filled transformers |
| EN 50216-1-2002 | 電源變壓器及電抗器配件 第1部分:總則 | Power transformer and reactor fittings - Part 1: General |
| EN 50216-2-2002 | 電源變壓器及電抗器配件 第2部分:帶保油箱的充液式變壓器和電抗器的氣動和油動繼電器 | Power transformer and reactor fittings - Part 2: Gas and oil actuated relay for liquid immersed transformers and reactors with conservator |
| EN 50216-3-2002+A1-2002 | 電源變壓器及電抗器配件 第3部分:未充氣的密封充液式變壓器和電抗器用保護繼電器 | Power transformes and reactor fittings - Part 3: Protective relay for hermetically sealed liquid-immersed transformers and reactors without gaseous cushion |
| EN 50216-4-2002 | 電源變壓器及電抗器配件 第4部分:主要配件(接地端子、排放和填充裝置、溫度計套和輪子) | Power transformer and reactor fittings - Part 4: Basic accessoiries (earthing terminal, drain and filling devices, thermometer pocket, wheel assembly) |
| EN 50216-5-2002+A1-2002 | 電源變壓器及電抗器配件 第5部分:液位指示器 壓力計和流量指示器 | Power transformer and reactor fittings - Part 5: Liquid level, pressure devices and flow indicators |
| EN 50216-6-2002 | 電源變壓器及電抗器配件 第6部分:冷卻設備 油漬變壓器的可移動的輻射器 | Power transformer and reactor fittings - Part 6: Cooling equipment; Removable radiators for oil-immersed transformers |
| EN 50216-7-2002 | 電源變壓器及電抗器配件 第7部分:變壓器油的電泵 | Power transformer and reactor fittings - Part 7: Electric pumps for transformer oil |
| EN 50243-2002 | 充液變壓器24kV和36kV以及5kA和8kV的室外套管 | Outdoor bushings for 24 kV and 36 kV and for 5 kA and 8 kA, for liquid filled transformers |
| EN 50299-2002 | 電壓為72.5kV至550KV設備的變壓器和電抗器用油浸電纜連接組件 | Oil-immersed cable connection assemblies for transformers and reactors having highest voltage for equipment U<(Index)m> from 72,5 kV to 550 kV |
| EN 50329-2003 | 鐵路應用 牽引變壓器 | Railway applications - Fixed installations - Traction transformers |
| EN 50336-2002 | 不大于36kV的變壓器和電抗器電纜箱的套筒 | Bushings for transformers and reactor cable boxes not exceeding 36 kV |
| EN 50386-2002 | 注液變壓器用1 kV及以下和 250 A 至 5 kA 的套管 | Bushings up to 1 kV and from 250 A to 5 kA, for liquid filled transformers |
| EN 50387-2002 | 注液變壓器用1 kV及以下和1.25 kA至5 kA 的母線套管 | Busbar bushings up to 1 kV and from 1,25 kA to 5 kA, for liquid filled transformers |
| EN 60044-3-2003 | 儀器變壓器 第3部分:組合式變壓器 | Instrument transformers - Part 3: Combined transformers ( 60044-3:2002) / Note: Endorsement notice |
| EN 60044-8-2002 | 儀器變壓器 第8部分:電流變壓器 | Instrument transformers - Part 8: Electronic current transformers (IEC 60044-8:2002) / Note: Endorsement notice |
| EN 60076-1-1997+A1-2000+A12-2002 | 電力變壓器 第1部分:總則 | Power transformers - Part 1: General (-1:1993, modified) |
| EN 60076-10-2001 | 電力變壓器 第10部分:聲級的測定 | Power transformers - Part 10: Determination of sound levels (-10:2001) |
| EN 60076-2-1997 | 電力變壓器 第2部分: | Power transformers - Part 2: Temperature rise (IEC 60076-2:1993, modified) |
| EN 60076-3-2001 | 電力變壓器 第3部分:絕緣水平、電介質試驗和空氣中的外間隙 | Power transformers - Part 3: Insulation levels, dielectric tests and external clearances in air (IEC 60076-3:2000 + Corrigendum 2000) |
| EN 60076-4-2002 | 電力變壓器 第4部分:閃電脈沖和開關脈沖試驗指南 電力變壓器和電抗器 | Power transformers - Part 4: Guide to the lightning impulse and switching impulse testing; Power transformers and reactors (IEC 60076-4:2002) / Note: Endorsement notice |
| EN 60076-5-2000 | 電力變壓器 第5部分:承受短路的能力(IEC 60076-5:2000) | Power transformers - Part 5: Ability to withstand short circuit (IEC 60076-5:2000) |
| EN 60146-1-3-1993 | 半導體變換器 第1-3部分:變壓器和電抗器 | Semiconductor convertors- General requirements and line commutated convertors- Part 1-3: Transformers and reactors (IEC 60146-1-3:1991) |
| EN 60310-1996 | 鐵路應用 運輸車輛的牽引變壓器和電感器 | Railway applications - Traction transformers and inductors on rolling stock (IEC 60310:1991, modified) |
| EN 60417-1/prAAA-2002 | 用于5945型小型變壓器的圖形符號:變壓器絕緣、短路試驗 修改草案AAA | IEC 60417: Graphical symbol for use on small transformers 5945 Pr: Isolating transformer, short-circuit proof |
| EN 60417-1/prAAAC-2002 | 用于5947型小型變壓器的圖形符號:變壓器絕緣安全、短路試驗 修改草案AAAC | IEC 60417: Graphical symbol for use on small transformers 5947 Pr: Safety isolating transformer, short-circuit proof |
| EN 60417-1/prAAAD-2002 | 用于小型變壓器5948型的圖形符號:變壓器絕緣微擾衰減法、總則 修改草案AAAD | IEC 60417: Graphical symbol for use on small transformers 5948 Pr: Perturbation attenuation isolating transformer, general |
| EN 60417-1/prAAAE-2002 | 用于小型變壓器5949型的圖形符號:變壓器絕緣微擾衰減法、短路試驗 修改草案AAAE | IEC 60417: Graphical symbol for use on small transformers 5949 Pr: Perturbation attenuation isolating transformer, short-circuit proof |
| EN 60417-1/prAAAF-2002 | 用于小型變壓器5950型的圖形符號:小型反應堆、總則 修改 草案AAAF | IEC 60417: Graphical symbol for use on small transformers 5950 Pr: Small reactor, general |
| EN 60417-1/prAAAG-2002 | 用于小型變壓器5951型的圖形符號:小型反應堆、非過載短路 修改草案AAAG | IEC 60417: Graphical symbol for use on small transformers 5951 Pr: Small reactor, non-overload proof |
| EN 60417-1/prAAAH-2002 | 用于小型變壓器5952型的圖形符號:小型反應堆、過載短路 修改草案AAAH | IEC 60417: Graphical symbol for use on small transformers 5952 Pr: Small reactor, overload proof |
| EN 60417-1/prAAB-2002 | 用于小型變壓器5946型 變壓器絕緣安全、非短路試驗的圖形符號 修改草案AAB | IEC 60417: Graphical symbol for use on small transformers 5946 Pr: Safety isolating transformer, non-short-circuit proof |
| EN 60417-1/prAAU-2002 | 用于小型變壓器5221/02型 變壓器絕緣 總則 圖形符號 修改草案AAU | IEC 60417: Graphical symbol for use on small transformers 5221/02: Isolating transformer, general |
| EN 60417-1/prAAV-2002 | 用于小型變壓器5222/02型 變壓器絕緣 總則 圖形符號 修改草案AAV | IEC 60417: Graphical symbol for use on small transformers 5222/02: Isolating transformer, general |
| EN 60417-1/prAAW-2002 | 用于小型變壓器5941型 自動轉換器 總則 圖形符號 修改草案AAW | IEC 60417: Graphical symbol for use on small transformers 5941 Pr: Auto-transformer, general |
| EN 60417-1/prAAX-2002 | 用于小型變壓器5942型 自動轉換器 非短路試驗 圖形符號 修改草案AAX | IEC 60417: Graphical symbol for use on small transformers 5942 Pr: Auto-transformer, non-short-circuit proof |
| EN 60417-1/prAAY-2002 | 用于小型變壓器5221/02型 自動轉換器 短路試驗 圖形符號 修改草案AAY | IEC 60417: Graphical symbol for use on small transformers 5943 Pr: Auto-transformer, short-circuit proof |
| EN 60417-1/prAAZ-2002 | 用于小型變壓器5944型 變壓器絕緣 非短路試驗 圖形符號 修改草案AAZ | IEC 60417: Graphical symbol for use on small transformers 5944 Pr: Isolating transformer, non-short-circuit proof |
| EN 60598-2-6-1994+A1-1997 | 燈具 第2分:特殊要求 第6:內裝變壓器的鎢絲燈燈具 | Luminaires - Part 2: Particular requirements - Section 6: Luminaires with built-in transformers for filament lamps (IEC 60598-2-6:1994) |
| EN 60726-2003 | 干式電力變壓器 | Dry-type power transformers (IEC 60726:1982 + A1:1986, modified) |
| EN 60852-4-1996 | 電信和電子設備用變壓器和電感器的外形尺寸 第4部分:使用YUI-2型鐵芯片的變壓器和電感器 | Outline dimensions of transformers and inductors for use in telecommunication and electronic equipment - Part 4: Transformers and inductors using YUI-2 laminations (IEC 60852-4:1996) |
| EN 61007-1997 | 電子和通信設備用變壓器和電感器 測量方法和試驗規程 | Transformers and inductors for use in electronic and telecommunication equipment - Measuring methods and test procedures (IEC 61007:1994, modified) |
| EN 61021-1-1997 | 電信和電氣設備用的變壓器和電感器的疊片鐵心包 第1部分:尺寸 | Laminated core packages for transformers and inductors used in telecommunication and electronic equipment - Part 1: Dimensions (IEC 61021-1:1990) |
| EN 61021-2-1997 | 電信和電氣設備用的變壓器和電感器的疊片鐵心包 第2部分:用YEE 2 疊片鐵芯的電性能 | Laminated core packages for transformers and inductors for use in telecommunication and electronic equipment - Part 2: Electrical characteristics for cores using YEE 2 laminations (IEC 61021-2:1995) |
| EN 61050-1992+A1-1995 | 空載輸出電壓超過1000V的管形放電用變壓器規范(一般叫做氖管變壓器) 一般要求和安全要求 | Transformers for tubular discharge lamps having a no-load output voltage exceeding 1000 V (generally called neon-transformers); general and safety requirements (IEC 61050:1991 + corrigendum 1992, modified) |
| EN 61203-1994 | 電工用合成有機酯 設備中變壓器酯類的維護指南 | Synthetic organic esters for electrical purposes - Guide for maintenance of transformer esters in equipment (IEC 61203:1992) |
| EN 61248-1-1997 | 電子和電信設備用變壓器和電感器 第1部分:通用規范 | Transformers and inductors for use in electronic and telecommunication equipment - Part 1: Generic specification (IEC 61248-1:1996) |
| EN 61248-2-1997 | 電子和電信設備用變壓器和電感器 第2部分:采用能力批準程序的信號變壓器分規范 | Transformers and inductors for use in electronic and telecommunication equipment - Part 2: Sectional specification for signal transformers on the basis of the capability approval procedure (IEC 61248-2:1996) |
| EN 61248-3-1997 | 電子和電信設備用變壓器和電感器 第3部分:采用能力批準程序的電源變壓器分規范 | Transformers and inductors for use in electronic and telecommunication equipment - Part 3: Sectional specification for power transformers on the basis of the capability approval procedure (IEC 61248-3:1996) |
| EN 61248-4-1997 | 電子和電信設備用變壓器和電感器 第4部分:采用能力批準程序的轉換供電方式(SMPS)的開關電源變壓器分規范 | Transformers and inductors for use in electronic and telecommunication equipment - Part 4: Sectional specification for power transformers for switched mode power supplies (SMPS) on the basis of the capability approval procedure (IEC 61248-4:1996) |
| EN 61248-5-1997 | 電子和電信設備用變壓器和電感器 第5部分:采用能力批準程序的脈沖變壓器分規范 | Transformers and inductors for use in electronic and telecommunication equipment - Part 5: Sectional specification for pulse transformers on the basis of the capability approval procedure (IEC 61248-5:1996) |
| EN 61248-6-1997 | 電子和電信設備用變壓器和電感器 第6部分:采用能力批準程序的電感器分規范 | Transformers and inductors for use in electronic and telecommunication equipment - Part 6: Sectional specification for inductors on the basis of the capability approval procedure (IEC 61248-6:1996) |
| EN 61248-7-1997 | 電子和電信設備用變壓器和電感器 第7部分:采用能力批準程序的高頻電感器和中頻變壓器分規范 | Transformers and inductors for use in electronic and telecommunication equipment - Part 7: Sectional specification for high-frequency inductors and intermediate frequency transformers on the basis of the capability approval procedure (IEC 61248-7:1997) |
| EN 61378-1-1998 | 交流器變壓器 第1部分:工業用變流變壓器 | Convertor transformers - Part 1: Transformers for industrial applications (IEC 61378-1-1997) |
| EN 61378-2-2001 | 交流器變壓器 第2部分:HVDC用變壓器 | Convertor transformers - Part 2: Transformers for HVDC applications (IEC 61378-2:2001) |
| EN 61558-1-1997+A1-1998+A11-2003 | 電力變壓器、電源裝置及類似設備的安全 第1部分:一般要求和試驗 | Safety of power transformers, power supply units and similar - Part 1: General requirements and tests (IEC 61558-1:1997, modified) |
| EN 61558-2-1-1997 | 電力變壓器、電源裝置及類似設備的安全 第2-1部分:通用分離變壓器的特殊要求 | Safety of power transformers, power supply units and similar - Part 2-1: Particular requirements for separating transformers for general use (IEC 61558-2-1:1997) |
| EN 61558-2-12-2001 | 電力變壓器、電源裝置及類似設備的安全 第2-12部分:恒壓變壓器的特殊要求 | Safety of power transformers, power supply units and similar - Part 2-12: Particular requirements for constant voltage transformers (IEC 61558-2-12:2001) |
| EN 61558-2-13-2000 | 電力變壓器、電源裝置及類似設備的安全 第2-13部分:通用自耦變壓器的特殊要求 | Safety of power transformers, power supply units and similar devices - Part 2-13: Particular requirements for auto-transformers for general use (IEC 61558-2-13:1999) |
| EN 61558-2-15-2001 | 電力變壓器、電源裝置及類似設備的安全 第2-15部分:醫療場所供電用的特殊要求 | Safety of power transformers, power supply units and similar - Part 2-15: Particular requirements for isolating transformers for the supply of medical locations (IEC 61558-2-15:1999, modified) |
| EN 61558-2-17-1997 | 電力變壓器、電源裝置及類似設備的安全 第2-17部分:開關模式電源變壓器的特殊要求 | Safety of power transformers, power supply units and similar - Part 2-17: Particular requirements for transformers for switch mode power supplies (IEC 61558-2-17:1997) |
| EN 61558-2-19-2001 | 電力變壓器、電源裝置及類似設備的安全 第2-19部分:擾動衰減變壓器的特殊要求 | Safety of power transformers, power supply units and similar devices - Part 2-19: Particular requirements for perturbation attenuation transformers (IEC 61558-2-19:2000) |
| EN 61558-2-2-1998 | 電力變壓器、電源裝置及類似設備的安全 第2-2部分:控制變壓器的特殊要求 | Safety of power transformers, power supply units and similar - Part 2-2: Particular requirements for control transformers (IEC 61558-2-2:1997) |
| EN 61558-2-20-2000 | 電力變壓器、電源裝置及類似設備的安全 第2-20部分:小型電抗器的特殊要求 | Safety of power transformers, power supply units and similar devices - Part 2-20: Particular requirements for small reactors (IEC 61558-2-20:2000) |
| EN 61558-2-23-2000 | 電力變壓器、電源裝置及類似設備的安全 第2-23部分:建筑工地用變壓器的特殊要求 | Safety of power transformers, power supply units and similar devices - Part 2-23: Particular requirements for transformers for construction sites (IEC 61558-2-23:2000) |
| EN 61558-2-3-2000 | 電力變壓器、電源裝置及類似設備的安全 第2-3部分:燃?xì)夂腿加忘c(diǎn)火變壓器的特殊要求 | Safety of power transformers, power supply units and similar devices - Part 2-3: Particular requirements for ignition transformers for gas and oil burners (IEC 61558-2-3:1999) |
| EN 61558-2-4-1997 | 電力變壓器、電源裝置及類似設備的安全 第2-4部分:通用的特殊要求 | Safety of power transformers, power supply units and similar - Part 2-4: Particular requirements for isolating transformers for general use (IEC 61558-2-4:1997) |
| EN 61558-2-5-1998 | 電力變壓器、電源裝置及類似設備的安全 第2-5部分:剃須刀變壓器和剃須刀電源裝置的特殊要求 | Safety of power transformers, power supply units and similar - Part 2-5: Particular requirements for shaver transformers and shaver supply units (IEC 61558-2-5:1997) |
| EN 61558-2-6-1997 | 電力變壓器、電源裝置及類似設備的安全 第2-6部分:通用安全隔離變壓器的特殊要求 | Safety of power transformers, power supply units and similar - Part 2-6: Particular requirements for safety isolating transformers for general use (IEC 61558-2-6:1997) |
| EN 61558-2-7-1997+A11-2003 | 電力變壓器、電源裝置及類似設備的安全 第2-7部分:玩具用變壓器的特殊要求 | Safety of power transformers, power supply units and similar - Part 2-7: Particular requirements for transformers for toys (IEC 61558-2-7:1997, modified) |
| EN 61558-2-8-1998 | 電力變壓器、電源裝置及類似設備的安全 第2-8部分:電鈴和電鬧鐘變壓器的特殊要求 | Safety of power transformers, power supply units and similar - Part 2-8: Particular requirements for bell and chime transformers (IEC 61558-2-8:1998) |
| EN 61558-2-9-2003 | 電力變壓器、供電裝置和類似產品的安全 第2-9部分:手持式三級鎢絲燈變壓器的特殊要求 | Safety of power transformers, power supply units and similar products - Part 2-9: Particular requirements for transformers for class III handlamps for tungsten filament lamps (IEC 61558-2-9:2002) / Note: Endorsement notice |
| EN 61596-1997 | 電感器和變壓器用磁氧化EP磁芯及其部件 尺寸 | Magnetic oxide EP-cores and associated parts for use in inductors and transformers - Dimensions (IEC 61596:1995) |
| EN 61797-1-1996 | 電信和電氣設備用變壓器和電感器 線圈骨架的主要尺寸 第1部分:疊層鐵芯線圈骨架 | Transformers and inductors for use in telecommunication and electronic equipment - Main dimensions of coil formers - Part 1: Coil formers for laminated cores (IEC 61797-1:1996) |
| EN 61823-2003 | 機場照明和信標用電氣設備 AGL系列變壓器 | Electrical installations for lighting and beaconing of aerodromes - AGL series transformers (IEC 61823:2002, modified) / Note: Endorsement notice |
| EN 5826-2003 | 電阻焊設備 變壓器 用于所有變壓器的一般規范 | Resistance welding equipment - Tranformers - General specifications applicable to all transformers ( 5826:1999) |
| EN ISO 7284-1996 | 電阻焊設備 汽車工業用多點點焊的兩個單獨副線圈的變壓器的特殊技術條件 | Resistance welding equipment - Particular specifications applicable to transformers with two separate secondary windings for multi-spot welding as used in the auto industry (ISO 7284:1993) |
| ENV 50232-1997 | 導航用地面照明電氣設備 減壓變壓器:設備規范和試驗 | Aeronautical ground lighting electrical installation - Isolating transformer: Equipment specifications and tests |
| HD 428.1 S1-1992+A1-1995 | 50 Hz、50 至2500 kVA、設備電壓不超過36 kV 的三相油浸式配電變壓器 第1部分:一般要求和設備電 | Three phase oil-immersed distribution transformers 50 Hz, from 50 to 2500 kVA with highest voltage for equipment not exceeding 36 kV; part 1: general requirements and requirements for transformers with highest voltage for equipment not exceeding 24 kV |
| HD 428.2.1 S1-1994 | 50 Hz、50 至2500 kVA、設備電壓不超過36 kV 的三相油浸式配電變壓器 第2部分:高壓和/或低壓端帶有電 | Three phase oil-immersed distribution transformers 50 Hz, from 50 to 2500 kVA with highest voltage for equipment not exceeding 36 kV - Part 2: Distribution transformers with cable boxes on the high voltage and/or low voltage side - Section 1: General req uirements |
| HD 428.2.2 S1-1997 | 50 Hz、50 至2500 kVA、設備電壓不超過36 kV 的三相油浸式配電變壓器 第2部分:高壓和/或低壓端帶有電 | Three-phase oil-immersed distribution transformers 50 Hz, from 50 to 2500 kVA with highest voltage for equipment not exceeding 36 kV - Part 2: Distribution transformers with cable boxes on the high-voltage and/or low-voltage side - Section 2: Cable boxes |
| HD 428.2.3 S1-1998 | 50 Hz、50 至2500 kVA、設備電壓不超過36 kV 的三相油浸式配電變壓器 第2部分:高壓和/或低壓端帶有電 | Three-phase oil-immersed distribution transformers 50 Hz, from 50 to 2500 kVA with highest voltage for equipment not exceeding 36 kV - Part 2: Distribution transformers with cable boxes on the high-voltage and/or low-voltage side - Section 3: Cable boxes |
| HD 428.3 S1-1994 | 50 Hz、50 至2500 kVA、設備電壓不超過36 kV 的三相油浸式配電變壓器 第3部分:設備電壓等于36 kV | Three phase oil-immersed distribution transformers 50 Hz, from 50 to 2500 kVA with highest voltage for equipment not exceeding 36 kV- Part 3: Supplementary requirements for transformers with highest voltage for equipment equal to 36 kV |
| HD 428.4 S1-1994 | 50 Hz、50 至2500 kVA、設備電壓不超過36 kV 的三相油浸式配電變壓器 第4部分:負載非正弦電流變壓器 | Three phase oil-immersed distribution transformers 50 Hz, from 50 to 2500 kVA with highest voltage for equipment not exceeding 36 kV- Part 4: Determination of the power rating of a transformer loaded with non-sinusoidal currents |
| HD 428.6 S1-2002 | 50 Hz、50 至2500 kVA、設備電壓不超過36 kV 的三相油浸式配電變壓器 第6部分:關于加壓波紋外殼的要 | Three phase oil-immersed distribution transformers 50 Hz, from 50 kVA to 2500 kVA with highest voltage for equipment not exceeding 36 kV - Part 6: Requirements and tests concerning pressurised corrugated tanks |
| HD 538.1 S1-1992+A1-1995 | 50 Hz、100 至2500 kVA、設備電壓不超過36kV的三相干式配電變壓器 第1部分:設備電壓不超過24kV的 | Three-phase dry-type distribution transformers 50 Hz, from 100 to 2500 kVA, with highest voltage for equipment not exceeding 36 kV; part 1: general requirements and requirements for transformers with highest voltage for equipment not exceeding 24 kV |
| HD 538.2 S1-1995 | 50 Hz、100 至2500 kVA、設備電壓不超過36kV的三相干式配電變壓器 第2部分:設備電壓等于36kV的變 | Three-phase dry-type distribution transformers 50 Hz, from 100 to 2500 kVA, with highest voltage for equipment not exceeding 36 kV - Part 2: Supplementary requirements for transformers with highest voltage for equipment equal to 36 kV |
| HD 538.3 S1-1997 | 50 Hz、100 至2500 kVA、設備電壓不超過36kV的三相干式配電變壓器 第3部分:非正弦電流負載變壓器功率 | Three-phase dry-type distribution transformers 50 Hz, from 100 to 2500 kVA, with highest voltage for equipment not exceeding 36 kV - Part 3: Determination of the power rating of a transformer loaded with non-sinusoidal current |
| HD 587 S1-1993 | 儀表變壓器 電壓為52 kV及以下的三相電壓變壓器 | Instrument transformers; Three-phase voltage transformers for voltage levels having U<(Index)m> up to 52 kV |
| prEN 126100-1991 | 分規范:用于能力批準的符合質量評定要求的電子設備用信號變壓器 | Sectional specification: signal transformers of assessed quality for use in electronic equipment for capability approval |
| prEN 126200-1991 | 分規范:用于能力批準的符合質量評定要求的電子設備用電源變壓器 | Sectional specification: power transformers of assessed quality for use in electronic equipment for capability approval |
| prEN 126300-1991 | 分規范:用于能力批準的符合質量評定要求的電子設備的開關模式供電設備用電源變壓器 | Sectional specification: power transformers of assessed quality for switched mode power supplies (SMPS) for use in electronic equipment for capability approval |
| prEN 126400-1991 | 分規范:用于能力批準的符合質量評定要求的電子設備用脈沖變壓器 | Sectional specification: pulse transformers of assessed quality for use in electronic equipment for capability approval |
| prEN 4068-001-1997 | 航空航天系列 飛機用變壓器整流器裝置 第001部分:技術規范 | Aerospace series - Transformer rectifier units for aircraft - Part 001: Technical specification |
| prEN 45510-2-1-2000 | 發電站設備的采購指南 第2-1部分::電氣設備 電力變壓器. | Guide for procurement of power station equipment - Part 2-1: Electrical equipment; Power transformers |
| prEN 45520-1994 | 采購指南 電氣設備 變壓器 | Guide for procurement - Electrical equipment - Transformers |
| prEN 50216-10-1-1996 | 電源變壓器及電抗器配件 第10-1部分:冷卻設備 油浸變壓器移動式的輻射器 | Power transformer and reactor fittings - Part 10: Cooling equipment - Section 1: Removable radiators for oil-immersed transformers |
| prEN 50216-10-4-1996 | 電源變壓器及電抗器配件 第10-4部分:冷卻設備 變壓器油的電泵 | Power transformer and reactor fittings - Part 10: Cooling equipment - Section 4: Electric pumpsets for transformer oil |
| prEN 50216-10-5-1997 | 電源變壓器及電抗器配件 第10-5部分:冷卻設備 電源變壓器油流量指示器 | Power transformer and reactor fittings - Part 10: Cooling equipment - Section 5: Oil flow indicators for power transformers |
| prEN 50216-11-1997 | 電源變壓器及電抗器配件 第11部分:油漬和干燥型配給變壓器輪子中心選擇與距離 | Power transformer and reactor fittings - Part 11: Choice and distance between centres of wheels for oil immersed and dry type distribution transformers |
| prEN 50216-8-1-1997 | 電源變壓器及電抗器配件 第8-1部分:放油裝置 對油浸配給變壓器取樣的放油塞 | Power transformer and reactor fittings - Part 8: Oil drain devices - Section 1: Draining plug with sampling for oil immersed distribution transformers |
| prEN 50216-8-2-1997 | 電源變壓器及電抗器配件 第8-2部分:放油裝置 不帶保油箱的浸油配給變壓器的加油孔 | Power transformer and reactor fittings - Part 8: Oil drain devices - Section 2: Filling openings for oil immersed distribution transformers without conservator |
| prEN 50236-1996 | 電源變壓器的電磁兼容性 | Electromagnetic compatibility for power transformers |
| prEN 50257-1996 | 性建筑物內的電壓Um大于1kV的設備用的電源變壓器和電抗器的使用和特殊設計特點 | Guide for the use and for particular design features for power transformers and reactors with highest voltage for equipment Um exceeding 1 kV, permanently incorporated in buildings |
| prEN 60076-11-2002 | 電力變壓器 第11部分: | IEC 60076-11: Power transformers - Part 11: Dry-type transformers |
| prEN 60076-8-1997 | 電力變壓器 第8部分:應用指南 | IEC 60076-8: Power transformers - Application guide |
| prEN 60296-2003 | 變壓器和開關設備用未使用過的礦物絕緣油規范 | IEC 60296, Ed. 3: Fluids for electrotechnical applications - Unused mineral insulating oils for transformers and switchgear |
| prEN 60310-2003 | 鐵路應用 運輸車輛的牽引變壓器和電感器 | Railway applications - Traction transformers and inductors on board rolling stock |
| prEN 60989-1994 | 單獨變壓器 自藕變壓器、可變頻率變壓器和電抗器 | Separating transformers, autotransformers, variable transformers and reactors (IEC 60989:1991, modified) |
| prEN 62041-2003 | 電源變壓器、供電部件和類似部件 電磁兼容要求 | IEC 62041, Ed. 1: Power transformers, power supply units, reactors and similar products - EMC requirements |
| 編號 | 中文名稱 | 英文名稱 |
青島恒豐友電氣隸屬于恒豐帥集團,是一家專業從事電力配電產品生產制造銷售的專業化電氣公司,主要從事配電變壓器、、等生產及化銷售。恒豐友電氣具備多年為歐洲西班牙、英國、德國等客戶提供服務的經驗。同時可提供變壓器鐵芯、變壓器線圈、變壓器外殼的定制生產。如果您有電力變壓器需求,非常期待與您的合作。/"> ;;WhatsApp:+86