當前位置:歐亞貿易網 > 技術中心 > 所有分類

| No. | 中文名稱 | Name |
|---|---|---|
| ANSI C12.9-2005 | 變壓器額定儀表用測試開關 | Test Switches for Transformer-Rated Meters |
| ANSI C57.12.10-1998 | 電壓不大于230千伏且容量為833/958至8333/10417千伏安單相及750/862至60000/80000/100000千伏安三相的變壓 | Transformers 230 kV and Below, 833/958 through 8333/10 417 kVA Single Phase, and 750/862 through 60 000/80 000/100 000 kVA Three Phase, Requirements for |
| ANSI C57.12.20-1997 | 變壓器.不大于500kVA的架空配電變壓器:高壓不大于34500伏、低壓不大于 7970/13800Y伏 | Transformers - Overhead-Type Distribution Transformers, 500 kVA and Smaller: High Voltage, 34 500 Volts and Below; Low Voltage, 7970/13 800Y Volts and Below |
| ANSI C57.12.24-2000 | 變壓器.不大于2500kVA的地下型三相配電變壓器:高壓不大于34500Y接地/19920伏、低壓不大于480伏.要求 | Transformers - Underground-Type Three-Phase Distribution Transformers, 2500 kVA and Smaller: High Voltage 34 500 Grd Y/19 920 Volts and Below; Low Voltage, 480 Volts and Below - Requirements |
| ANSI C57.12.50-1981 | 高壓601至34500伏,低壓120至600伏,容量單相1至500千伏安和三相15至500千伏安,通風干式配電變壓器的要求 | Ventilated Dry-Type Distribution Transformers, 1 to 500 kVA, Single-Phase and 15 to 500 kVA, Three-Phase, with High-Voltage 601 to 34 500 Volts, Low-Voltage 120 to 600 Volts, Requirements for; Correction June 1982 |
| ANSI C57.12.51-1981 | 三相,高壓601至34500伏,低壓208Y/120至4160伏容量不小于501千伏安,通風干式電力變壓器的要求 | Requirements for Ventilated Dry-Type Power Transformers, 501 kVA and Larger, Three-Phase, with High-Voltage 601 to 34 500 Volts, Low-Voltage 208Y/120 to 4160 Volts |
| ANSI C57.12.52-1981 | 三相,高壓:601至34500伏,低壓:208Y/120至4160伏,容量不小于501千伏安,密封干式電力變壓器的要求 | Requirements for Sealed Dry-Type Power Transformers, 501 kVA and Larger, Three-Phase, with High-Voltage 601 to 34 500 Volts, Low-Voltage 208Y/120 to 4160 Volts |
| ANSI C57.12.55-1987 | 變壓器.包括成套變電所在內的成套設備用.一致性標準 | Transformers - Dry-Type Transformers Used in Unit Installations, Including Unit Substations - Conformance Standard |
| ANSI C82.7-1983 | 水銀燈變壓器.恒定電流(系列)供電型 | Mercury Lamp Transformers - Constant-Current (Series) Supply Type |
| ANSI C82.8-1988 | 燈變壓器.白熾燈變壓器.恒定電流(系列)供電型 | Lamp Transformers - Incandescent Filament Lamp Transformers - Constant-Current (Series) Supply Type |
| ANSI C82.9-1996 | 高亮度放電和低壓鈉燈、鎮流器和變壓器.定義 | High-Intensity-Discharge and Low-Pressure Sodium Lamps, Ballasts and Transformers - Definitions |
| ANSI C82.9b-1998 | 電燈鎮流器.高強度放電和低壓鈉燈鎮流器和變壓器的定義 | Electric Lamp Ballasts - High-Intensity-Discharge and Low-Pressure Sodium Lamps, Ballasts and Transformers - Definitions |
| ANSI/ASTM A1009-2000 | 高頻(10KHz-1MHz)電源變壓器和過濾電感器軟磁化錳鋅鐵芯材料規范 | Specification for Soft Magnetic MnZn Ferrite Core Materials for High Frequency (10KHz to 1MHz) Power Transformer and Filter Inductor Applications |
| ANSI/IEEE 111-2000 | 寬帶(大于10倍頻程)變壓器標準 | Standard for Wide Band (Greater than 1 Decade) Transformers |
| ANSI/IEEE 1538-2000 | 充液變壓器的繞組的測定指南 | Guide for Determination of Maximum Winding Temperature Rise in Liquid Filled Transformers |
| ANSI/IEEE 295-1969 | 電子設備電力變壓器 | Electronics Power Transformers |
| ANSI/IEEE 388-1992 | 電子功率變換設備中的變壓器和感應線圈 | Transformers and Inductors in Electronic Power Conversion Equipment |
| ANSI/IEEE 389-1996 | 測試電子電路變壓器和感應器的推薦實施規程 | Recommended Practice for Testing Electronic Transformers and Inductors |
| ANSI/IEEE 436-1991 | 電子電路變壓器產生電暈(局部放電)的測量指南 | Guide for Making Corona (Partial Discharge) Measurements on Electronics Transformers |
| ANSI/IEEE 62-1995 | 電力設備的診斷現場試驗指南.第1部分:充油電力變壓器、調節器和電抗器 | Guide for Diagnostic Field Testing of Electric Power Apparatus - Part 1: Oil Filled Power Transformers, Regulators, and Reactors |
| ANSI/IEEE 638-1992 | 核電站用IE級變壓器的合格鑒定 | Standard for Qualification of Class 1E Transformers for Nuclear Power Generating Stations |
| ANSI/IEEE C37.108-2002 | 保護網絡變壓器指南 | Guide for the Protection of Network Transformers |
| ANSI/IEEE C37.91-2000 | 電力變壓器的保護繼電器應用指南 | Protective Relay Applications to Power Transformers, Guide for |
| ANSI/IEEE C57.100-1999 | 油浸式配電變壓器熱評定試驗規程 | Distribution Transformers, Test Procedure for Thermal Evaluation of Oil-Immersed |
| ANSI/IEEE C57.105-1992 | 三相配電系統變壓器連接申請 | Application of Transformer Connections in Three-Phase Distribution Systems |
| ANSI/IEEE C57.109-1993 | 液浸式變壓器穿越故障電流持續時間的指南 | Guide for Liquid-Immersed Transformer Through-Fault Current Duration |
| ANSI/IEEE C57.110-2004 | 施加非正弦負載電流時變壓器性能確定的推薦實施規程 | Recommended Practice for Establishing Transformer Capability When Supplying Nonsinusoidal Load Currents |
| ANSI/IEEE C57.111-1995 | 硅絕緣液體驗收指南和在變壓器中的維護 | Guide for Acceptance of Silicone Insulating Fluid and Its Maintenance in Transformers |
| ANSI/IEEE C57.113-2002 | 充液電力變壓器和并聯電抗器的局部放電測量指南 | Guide for Partial Discharge Measurement in Liquid-Filled Power Transformers and Shunt Reactors |
| ANSI/IEEE C57.116-1990 | 直接連于發電機的變壓器指南 | Guide for Transformers Directly Connected to Generators |
| ANSI/IEEE C57.117-1986 | 公用電力系統的電力變壓器和并聯電抗器失效數據報告指南 | Reporting Failure Data for Power Transformers and Shunt Reactors on Electric Utility Power Systems, Guide for |
| ANSI/IEEE C57.119-2002 | 超出銘牌額定值的負荷下進行油浸電力變壓器升溫試驗的推薦慣例 | Recommended Practice for Performing Temperature Rise Tests on Oil Immersed Power Transformers at Loads Beyond Nameplate Ratings |
| ANSI/IEEE C57.12.01-2005 | 包括固體澆鑄和/或樹脂密封繞組的干式配電和電力變壓器的標準.一般要求 | Standard General Requirements for Dry-Type Distribution and Power Transformers Including Those with Solid-Cast and/or Resin Encapsulated Windings |
| ANSI/IEEE C57.12.20-2005 | 500 kVA及更小的頂置式配電變壓器的標準:高壓34500V及以下、低壓7970/13800Y伏特及以下 | Standard for Overhead Type Distribution Transformers, 500 kVA and Smaller: High Voltage, 34 500 Volts and Below; Low Voltage, 7970/13 800Y Volts and Below |
| ANSI/IEEE C57.12.23-2002 | 變壓器.帶可分離絕緣高壓連接器的地下型、自冷式單相配電變壓器.高壓(24940GrdV/14400V及以下)和低壓(240/1 | Transformers - Underground-Type, Self-Cooled, Single-Phase Distribution Transformers with Separable, Insulated, High-Voltage Connectors; High Voltage (24 940 GrdY/14 400 V and Below) and Low Voltage (240/120 V, 167 kVA and Smaller) |
| ANSI/IEEE C57.12.34-2004 | 底座安裝的隔室型自冷式三相配電變壓器2500 kVA及更小:高壓34500 GrdY/19920伏及以下、低壓480伏及以下的要 | Standard Requirements for Pad-Mounted, Compartmental-Type, Self-Cooled, Three-Phase Distribution Transformers, 2500 kVA and Smaller: High-Voltage, 34 500 GrdY/19 920 Volts and Below; Low Voltage, 480 Volts and Below |
| ANSI/IEEE C57.12.35-1996 | 配電變壓器的標準條形編碼 | Standard Bar Coding for Distribution Transformers |
| ANSI/IEEE C57.12.56-1994 | 通風干燥型電力和配電變壓器絕緣系統熱評價的試驗程序 | Test Procedure for Thermal Evaluation of Insulation Systems for Ventilated Dry-Type Power and Distribution Transformers (reinstatement of administratively withdrawn standard) |
| ANSI/IEEE C57.12.58-1991 | 線圈瞬態電壓分析指南 | Guide for Conducting a Transient Voltage Analysis of a Dry Type Transformer Coil |
| ANSI/IEEE C57.12.59-2002 | 干式變壓器全故障電流持續時間指南 | Guide for Dry-Type Transformer Through-Fault Current Duration |
| ANSI/IEEE C57.12.60-1998 | 固體澆鑄和樹脂密封的電力和配電變壓器絕緣系統熱評定試驗程序指南 | Guide for Test Procedures for Thermal Evaluation of Insulation Systems for Solid Cast and Resin-Encapsulated Power and Distribution Transformers |
| ANSI/IEEE C57.12.70-2000 | 輸電及電力變壓器用終端標志和連接標準 | Standard Terminal Markings and Connections for Distribution and Power Transformers |
| ANSI/IEEE C57.12.80-2002 | 電力分配變壓器術語 | Terminology for Power and Distribution Transformers |
| ANSI/IEEE C57.12.90-1999 | 油浸式配電、電力和調壓變壓器的試驗規程及電力和配電變壓器短路試驗指南 | Test Code for Liquid-Immersed Distribution, Power and Regulating Transformers and Guide for Short-Circuit Testing of Distribution and Power Transformers |
| ANSI/IEEE C57.120-1992 | 電力變壓器和電抗器的損耗評價指南 | Loss Evaluation Guide for Power Transformers and Reactors |
| ANSI/IEEE C57.123-2002 | 變壓器損失測量指南 | Guide for Transformer Loss Measurement |
| ANSI/IEEE C57.124-1991 | 干式變壓器表觀電荷部分放電和測量的檢測 | Detection of Partial Discharges and the Measurement of Apparent Charge in Dry Type Transformers |
| ANSI/IEEE C57.125-2005 | 電力變壓器和分流扼流器故障研究、記錄和分析指南 | Guide for Failure Investigation, Documentation, and Analysis for Power Transformers and Shunt Reactors |
| ANSI/IEEE C57.13-2003 | 儀表用變壓器標準要求 | Standard Requirements for Instrument Transformers |
| ANSI/IEEE C57.13.1-1981 | 繼電器用的電流變壓器現場測試指南 | Field Testing of Relaying Current Transformers |
| ANSI/IEEE C57.13.2-2005 | 儀表用變壓器標準合格測試程序 | Standard Conformance Test Procedure for Instrument Transformers |
| ANSI/IEEE C57.13.3-2005 | 儀表用變壓器次級線圈電路和外殼接地指南 | Guide for Grounding of Instrument Transformer Secondary Circuits and Cases |
| ANSI/IEEE C57.13.6-2005 | 高精度儀表變壓器標準 | Standard for High Accuracy Instrument Transformers |
| ANSI/IEEE C57.134-2000 | 干式變壓器熱斑溫度測定指南 | Guide for Determination of Hottest Spot Temperature in Dry Type Transformers |
| ANSI/IEEE C57.135-2001 | 移相變壓器的應用、規范和測試指南 | Guide for the Application, Specification and Testing of Phase-Shifting Transformers |
| ANSI/IEEE C57.136-2000 | 額定功率大于500kVA的油浸式電力變壓器和并聯電抗器的聲級抑制和測定指南 | Guide for Sound Level Abatement & Determination for Liquid-Immersed Power Transformers & Shunt Reactors Rated Over 500 kVA |
| ANSI/IEEE C57.138 (R200x)-1998 | 配電變壓器常規脈沖試驗的推薦實施規程 | Recommended Practice for Routine Impulse Test for Distribution Transformers |
| ANSI/IEEE C57.138-1998 | 配電變壓器常規脈沖試驗推薦慣例 | Recommended Practice for Routine Impulse Test for Distribution Transformers |
| ANSI/IEEE C57.144-2004 | 變壓器標準的米制轉換指南 | Guide for Metric Conversion of Transformer Standards |
| ANSI/IEEE C57.146-2005 | 硅樹脂浸變壓器產生氣體的說明指南 | Guide for the Interpretation of Gases Generated in Silicone-Immersed Transformers |
| ANSI/IEEE C57.18.10-1998 | 半導體電力要求和標準實施規程 | Standard Practices and Requirements for Semiconductor Power Rectifier Transformers |
| ANSI/IEEE C57.91-2004 | 礦物油浸式變壓器的加載指南 | Guide for Loading Mineral-Oil-Immersed Transformers |
| ANSI/IEEE C57.93-1995 | 液浸式電力變壓器的安裝指南 | Guide for Installation of Liquid Immersed Power Transformers |
| ANSI/IEEE C57.94-2000 | 干式通用配電及電力變壓器的安裝、應用、操作和維護的推薦規程 | Recommended Practice for Installation, Application, Operation, and Maintenance of Dry-Type General-Purpose Distribution and Power Transformers |
| ANSI/IEEE C57.96-1999 | 負載干式配電和電源變壓器指南 | Distribution and Power Transformers, Guide for Loading Dry-Type (appendix to ANSI C57.12 standards) |
| ANSI/IEEE C57.98-1993 | 變壓器脈沖試驗指南 | Impulse Tests, Guide for Transformer (appendix to ANSI/IEEE C57.12.90) |
| ANSI/NECA 409-2002 | 干式變壓器的安裝和維護的推薦規程 | Recommended Practice for Installing and Maintaining Dry-Type Transformers |
| ANSI/NECA 410-2005 | 充液變壓器安裝和維修標準 | Standard for Installing and Maintaining Liquid-Filled Transformers |
| ANSI/NETA MTS7.2.1-2001 | 干式變壓器NETA維護測試規范:氣冷600V及以下.小型(167kV單相,500kVA三相及更小)和氣冷600V及以下.大型(大于 | NETA Maintenance Testing Specifications for Dry-Type Transformers: Air-Cooled, 600 Volts and Below - Small (167 kV Single-Phase, 500 kVA Three-Phase, and Smaller) and Air-Cooled, All Above 600 Volts and 600 Volts and Below - Large (Greater than 167 kV Single-Phase and 500 kVA Three-Phase) |
| ANSI/NETA MTS7.2.2-2001 | 充液變壓器維護測試規范 | Maintenance Testing Specifications for Liquid-Filled Transformers |
| ANSI/SCTE 68-2003 | 無源電壓降:匹配變壓器75ohm到300ohm | Drop Passives: Matching Transformers 75 ohm to 300 ohm |
| ANSI/UL 1310-2005 | 直接插入式變壓器設備 | Direct Plug-in Transformer Units |
| ANSI/UL 1561-2005 | 干式通用和電力變壓器 | Dry-Type General Purpose and Power Transformers |
| ANSI/UL 506-2005 | 專用變壓器 | Specialty Transformers |
| ANSI/UL 551-1993 | 變壓器型弧焊機 | Transformer-Type Arc-Welding Machines |
| ANSI/UL 697-2004 | 玩具變壓器 | Toy Transformers |
| ASTM A 1009-2005 | 高頻(10kHz-1MHz)電力變壓器和濾波感應器用軟磁性MnZn鐵芯材料標準規范 | Standard Specification for Soft Magnetic MnZn Ferrite Core Materials for High Frequency (10 kHz-1 MHz) Power Transformer and Filter Inductor Applications |
| ASTM D 2759-2000 | 在正壓力下從變壓器中抽取氣體樣品的標準實施規程 | Standard Practice for Sampling Gas from a Transformer Under Positive Pressure |
| ASTM D 3305-1994 | 從變壓器中抽取小體積氣體樣品的標準實施規程 | Standard Practice for Sampling Small Gas Volume in a Transformer |
| UL 1411-1998 | 音頻、無線電和電視類裝置用變壓器與電機變壓器 | (Transformers and motor transformers for use in audio-, radio-, and television-type appliances ) |
| UL 1561-1999 | 干式通用電力變壓器 | (Dry-type general purpose power transformers ) |
| UL 1562-1999 | 干式600V以上變壓器、配電系統 | (Transformers, distribution, dry-type over 600 volts ) |
| UL 1585-1998 | 2類和3類變壓器 | (Class 2 and class 3 transformers ) |
| UL 1876-2001 | 電子設備中隔離和反饋信號用變壓器 | (Isolating signal and feedback transformers for use in electronic equipment ) |
| UL 2161-1996 | 氖變壓器和電力電源 | (Neon transformers and power supplies ) |
| UL 551-1994 | 變壓器型弧焊機 | (Transformer-type arc-welding machines ) |
| UL 697-1998 | 玩具用變壓器 | (Toy transformers ) |
| No. | Name | Name |
青島恒豐友電氣隸屬于恒豐帥集團,是一家專業從事電力配電產品生產制造銷售的專業化電氣公司,主要從事配電變壓器、、等生產及化銷售。恒豐友電氣具備多年為歐美、中東客戶提供服務的經驗。同時可提供變壓器鐵芯、變壓器線圈、變壓器外殼的定制生產。如果您有電力變壓器需求,非常期待與您的合作。"> ;;WhatsApp:+86